such as? g Soda ring bag? That’s for sure! Today we will tell you how to prepare. Beautiful bag Using nothing more than soda rings you get and save every time you drink. Coca-Cola can both 7 and up. this handicraft It requires some skills with your hands. But with our advice It shouldn’t be very complicated. I hope you like it!
this bag Can be made in many sizes It depends on how many rings you have and how much work you want to invest in this bag. The hardest part might be tying the loops into the fabric from which we’ll assemble the bag later. But don’t be discouraged! Today we will explain in detail how to do it together. with sharing various videos So you can see the process of making beautiful bags. These are step by step.
Materials and tools for making soda ring bags
Let’s see how to make a soda ring-shaped bag. For you to have a beautiful bag that you can use every day. You will need the following materials:
- refreshing ring As many as your model requires or your bag size requires.
- Mold (wallet lining)
- brooch
- Wool or fine thread
- Needle (knitting)
- pliers
- tweezers
How to make a soda ring bag step by step
Let’s take a look at a simple step-by-step how to make a bag with a soda loop, and the end result is a bag like the one seen in the picture below.
First step: prepare the ring
The first thing we need to do is give the ring of the can a good wash to keep it clean and shiny.
for this We put it in a bowl with water, to which you can add a few drops of vinegar.. We let the vinegar take effect for at least an hour and then dry it well.
To dry all rings at once You can place them all on any table or surface and with The help of the dryer makes them dry.This will save time and it will be very dry.
Step Two: Prepare the Lining
Once we get all the rings from the dry can. We began to prepare what would be ours. Lining that will mold to the inside of the bag.You’ll need a lining, which is easily available at haberdashery stores.
Cut the lining as if it were Mold for bag shape. In our case, the lining will need to be a little. circlebut If you make a small bag Of that type of wallet, there may be More square or rectangular shape
Step Four: We begin to knit wool.
Our loop bag will be a bag that will come with feathers to connect the loop. Therefore, we must start weaving in such a way that We can begin to take shape. Into the bag we will add a ring.
We start by doing The base has about fifty chains. When it’s finished, we do it. Two more (extra) chains, we return to chain 50. and we do half point And from here we count and We scored six and a half points. (The two points we have already scored are counted as two and a half points or one point.)
We move on to the next point and continue. knit half a point like this until we reach the other side where we get six and a half points again and We came back for half a point.
When the base is finished We continue the chain of half points. The entire base is closed with a sliding stitch where we started. To add content to the base We can keep adding half a point. We will continue until we reach the desired height.
Step Four: We begin to combine the sheets.
Now we have the step to begin attaching the sheets or sewing them to the base we woven previously. Take the first plate or ring and place it in the corner.. Insert the needle or hook through what you have knitted and through the center of the ring. Connect the bases with semicircular points. Now cover the entire sheet with wool or thread. You need to knit in several half stitches (nine is enough), and once the first piece of fabric is closed, We will sew a half seam to the fabric.
So you must Join each ring. What you need to assemble your can bottle bag
Fifth step: we sew the lining.
Once you have assembled the entire bag with the wool and badge. It’s time to sew the lining. To do this, you need to turn the bag over and using a little sewing thread and a needle, you need to sew the entire lining to the edge of the bag so that when you turn it over again, the lining is still firmly attached and is where we are. to put things away
Make a ring bag out of wire.
Another easy way to make a bag with soda loops is to connect each loop. Then, once you have the length you want, Attach them to the wire to create a base.
The rings will continue to be joined together until the entire length and width of the bag has been reached. When it was time to shape it, the wire was brought back into shape again. Close part of bag that must go together
Finally, let’s do the part. The handle has two or three soda rings assembled together and connected by wire. or something similar to keep and follow the ring over creative intervals until you get the handle to the desired length.
Ideas for your bag with rings
Also, if you want to keep the bag from being gray, you can. painted ring The items you will use in the bag can then be combined with other items or clothing you have in your closet to get the look you want.
In this case, the ideal is able. The ring was previously painted. which you need to place on newspaper or something similar. Then use spray paint Let it dry and then flip it over to paint the other side. Once everything is completely dry, it’s time to start creating your new soda ring bag.
If you are creative and come up with a golden beer ring. You can play with these colors. And there are also some cans that have rings with inscriptions or have other colors, for example. Pepsi ring which is blue It wouldn’t be bad if they all got the same ring. But of course you’ll be drinking multiple cans of the same soda.
Video on how to make soda ring bags
We have already explained how to make a bag with a soda ring. But if you want to see how to do it step by step. We will leave you with these videos that will no doubt help you.